• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

Why is My Car Ignition Locked?

There are several reasons why your ignition in your car may be locked. One reason is that the key is dirty or has a broken wafer inside it. This can be repaired by sliding the key into and out of the cylinder several times.

The pins on the lock cylinder may also be stuck. You can tap the cylinder lightly with a small tack-hammer.

Check the Battery

If the car is in Park or neutral, but won't turn on when you insert the key into the ignition, it might be an issue with the transmission shifter switch. You can fix this by moving the gear shifter upwards or downward to get the vehicle into the correct gear.

If the car doesn't turn, the problem could be with the neutral safety cable or the shifter on the transmission. A mechanic or a local auto ignition key replacement locksmith can fix these problems.

It's also possible that the ignition cylinder has worn out. Over time, the ignition as well as the key will wear out, causing them to become difficult to insert or remove. A lubricant like silicon lock grease can address this issue, letting the wafers to slide into place.

The key can become clogged by lint from your pockets as well as adhesive from tape used to secure packages. This prevents the key from sliding into the ignition. Clean the key with a cloth or a cleaner like Triflow, to solve this problem. You can also test a spare key to determine if the problem is the ignition or the key.

While the key is in ignition, you can tap it with a small piece of hammer. This will create a tiny vibration that could cause enough vibration to loosen the ignition's wafers and allow them to slide in the right position. However, you must be cautious not to harm the key or the ignition cylinder.

If all of the above methods fail, it's likely to contact a locksmith ignition replacement cost or automotive mechanic to have it examined. It could be that the key is broken inside the ignition or it may be time to replace the entire thing. If the problem is with the key the locksmith can create a new one for you. If the cylinder for the ignition is the problem then you'll need to bring the car to a repair shop in order for it to be repaired. These problems are usually easy to fix.

Make sure you check the steering Wheel

A common issue that can prevent the ignition from turning is the steering wheel being locked. It can happen if drivers accidentally engage the steering wheel while they exit or get into the vehicle. This usually happens by yanking the wheel while resting it against their body. It can also happen when an individual in the back seat is unable to stop it when they climb out of the car.

Luckily, this is an easy fix that does not require a trip to a mechanic or a locksmith. First, ensure that the gear shift is either in neutral or Park. If it's not you can gently pull or push the gear shifter until it shifts to one of these positions. It is also essential to press the brake or activate the handbrake before you attempt to turn the key.

If the wheel isn't locked an inspection of the steering column will show if the key has been engaged with the lock. A small "Lock label is typically located in the lower area of the ignition circle. You can easily disengage this by gently jiggling or pulling the keys with moderate force. It is important to not apply too much pressure since this can damage the key, or even damage a wafer inside the lock cylinder.

Another option is to use an alternate key to see if it can disengage the lock. This could mean that the key is worn and cannot engage the wafers inside the lock cylinder. A professional at Karl Chevrolet Webster City can make a new key if this is the case.

If the new key still isn't engaging, a quick spray of penetrating oil could assist. Just apply a small amount around the ignition, and keyhole, then gently tap or jiggle it until it starts to work. If this doesn't work, you will likely need to see a specialist at your local auto dealership. They'll be able to provide you with a new key, and will also replace the ignition cylinder, should it be necessary.

Check the Key

It could be that your key has been damaged if it does not engage in the ignition. Try getting rid of any foreign material that is on the key (lint and adhesive from packing tape, etc). You can also try rubbing alcohol on the key or Goo Gone to see if it aids.

If the pins inside the lock aren't moving properly when you insert your key, it is possible that they are stuck. You can test the spare key by gently removing it of the ignition after having put it in. You should be in a position to feel and hear the pins moving inside. If not, you could apply lubrication to the pins using powdered graphite. You can purchase graphite in small tubes that can be put directly into the keyhole. This will allow the pins to slide into position when you insert the key, and prevent them from getting stuck.

It is possible that your key has worn out or damaged and isn't able to connect with the pins in the ignition cylinder. This could cause the cylinder to stop to turn, and prevent you from starting your car ignition switch replacement. If this is the case you'll need to take your vehicle to an auto locksmith or repair shop for assistance.

If you are able to turn your car using a spare key and you've ruled out issues with the steering wheel or battery it could be because the ignition cylinder has worn out. You can try to loosen the lock with an abrasive screwdriver or handle of smaller hammers. Don't use the head. Sometimes, a gentle tap on the cylinder will release it and allow you to turn your Car Ignition Repair key. If this does nothing, you'll need to have the lock cylinder replaced by a mechanic.

Check the Ignition Socket

The ignition socket is where your key is inserted and slides out of place when inserted. Most of the time, it gets filled with debris or simply a result of regular wear and tear. Try putting some silicon lock lubricant (like WD-40) into the ignition to make things move along.

You can also use a small hammer, and tap gently on the inside of the ignition to loosen or reset the pins that are out of alignment. Be very cautious not to overdo it or you could cause serious damage to the ignition switch.

Before you try this, make sure the gearbox of your car is either in park or neutral. Many newer cars have an option to lock the steering wheel when it is not in park or neutral, which can prevent the key from turning into the ignition.

If you have tried all of these steps and your key still won't turn, it could be that the ignition housing needs to be replaced. It is important to remember that different vehicles have different procedures for replacing the ignition cylinder.

Generally, this means taking off the plastic cover that is over the steering column and ignition assembly. To remove it, you'll have to adjust the tilt-wheel in its lowest position. Then, loosen any fasteners that are holding it in the position.

After you have removed the cover, you'll need to take off the old ignition cylinder from the steering column. Then, you'll have to compare the new ignition cylinder you purchased with the one that was removed to ensure that they're identical. Once this step is complete, the new ignition cylinder will be installed in the same manner that the previous one was removed.

It is possible that, despite our best efforts, the ignition could be damaged and require to be replaced. If this happens, it is recommended to contact Tempe Locksmith Tempe Locksmith for assistance. A locksmith can assist you in selecting the right replacement and install it properly to ensure that your car will be able to start up again.